HOME
Products
Power Distribution
Battery Terminals & Post Kits
Protected Positive and Negative Remote Battery Connection Post Kit — Paired Service Connection | Included Protective Components | Panel, Bulkhead or Surface Integration

PROTECTED BATTERY ACCESS KIT

Protected Positive and Negative Remote Battery Connection Post Kit — Paired Service Connection | Included Protective Components | Panel, Bulkhead or Surface Integration

DAIERTEK BCP-3K is a protected remote battery connection kit for creating an organized positive-and-negative service interface away from the battery. Its paired architecture is intended for vehicle and equipment installations where both polarities must be accessible at a defined maintenance or connection point. Protective components are included to support polarity identification and reduce unintended contact around the connection points. The kit-based format helps buyers source the mating posts and protective parts as one coordinated assembly instead of building the interface from unrelated components. BCP-3K should be selected from the approved assembly drawing rather than from appearance alone. Confirm stud size, cable-lug interface, mounting method, panel or surface geometry, insulation spacing, kit contents, current rating and environmental requirements before sampling or production.

Positive + negative

Connection architecture

Paired kit

Supply format

Included

Protective components

Remote access

Primary function

Product drawing, material declaration and available compliance documents can be requested for the specific model and production configuration. Certification scope must be verified against the applicable document before publication or customer submission.

Product Details

01 Coordinated two-pole service interface
Creates a defined positive-and-negative access point for approved charging, maintenance or auxiliary power procedures.
02 Included protective components
The coordinated kit supports clearer polarity identification and reduces exposed conductive surfaces when the connection is not in use. Exact environmental protection must be confirmed by test evidence.
03 Installation-led selection
The correct configuration depends on the panel or surface, available rear clearance, lug stack, cable routing and service-tool access. Use the model drawing to approve the complete interface.

Specifications

Model	BCP-3K
Product Type	Protected Remote Battery Connection Post Kit
Connection Architecture	Positive and Negative Pair
Primary Interface	Remote Battery-Cable Connection
Protective Components	Included
Mounting	Panel, Bulkhead or Surface Installation
Electrical Function	Passive Connection Kit; No Fuse or Disconnect

Selection note: Treat the terminal, cable, lug, fastener, insulation and circuit-protection arrangement as one system. Verify the controlled drawing and approved technical data before sampling or production.

Compare Models

Compare connection architecture before comparing dimensions. These models serve different functions and are not automatically interchangeable.

Model	Product Type	Mounting	Connection Architecture
BTP-2M-M8	M8-to-tapered-post adapter set	Direct to threaded battery terminal	Positive + negative pair
BCP-1	Single remote connection post	Through-panel / bulkhead	Single post
BCP-1K	Remote post kit with cable leads	Bracket / panel	Positive + negative pair
BCP-2	Covered through-panel connector	Through-panel	Single protected post
BCP-3K Current Product	Protected remote post kit	Panel / bulkhead / surface	Positive + negative kit
BT-21	Multi-connection battery terminal	Direct to battery post	12 connection positions

Use a direct terminal or adapter when the connection starts at the battery. Use a remote post when the battery connection must be brought to an accessible panel or service point.

Applications

Remote battery service stations

Create an identified two-pole point for approved battery charging and maintenance procedures.

Commercial and special vehicles

Locate battery access near a service panel while the battery remains protected elsewhere in the vehicle.

RV, marine and off-road equipment

Organize positive and negative cable access where compartment layout or equipment placement limits direct battery access.

Application examples describe potential use cases, not verified fitment to a particular vehicle. Confirm polarity, cable size, protection, mounting space, environmental exposure and the approved service procedure before installation.

Complete Your Battery Connection System

Complementary isolation, circuit-protection, cable and power-distribution products for coordinated automotive, RV, marine and special-vehicle electrical systems.

Model	Product	Button
ASW-A701	Battery Disconnect Switch	View Product
ANL-04	ANL Fuse Holder	View Product
4AWG200C-21-1.2M-SC2510	4 AWG Cable Assembly	View Product
BB250-T4M8S3-C-2	Power Distribution Bus Bar	View Product

Technical information for BCP-3K

Contact DAIERTEK for the controlled dimension drawing, installation interface, material information, available compliance documentation and sample support. Include the model number, battery or panel interface, cable schedule and target application so the enquiry can be routed correctly.

Request Technical Documents